update version to 0.3.1 for the jogging fix

Reviewed-on: #4

AGENTS.md

@@ -60,7 +60,7 @@ Everything is configured through environment variables — see README.md for the
 ## Test
 
 ```bash
-uv run pytest      # 86 tests, no robot and no dataflow needed
+uv run pytest      # 92 tests, no robot and no dataflow needed
 uv run ruff check .
 ```
 
@@ -183,6 +183,15 @@ A typed optional input therefore forces the example dataflow to wire it. `reques
 ## Rules
 
 - Do not mention AI tools in commit messages or documentation.
+- **A velocity is set on the controller once and held.** `set_cartesian_velocity` passes no
+  duration and skips an unchanged velocity, because re-arming makes the controller re-plan
+  the same motion and the arm steps instead of travelling — four times a second is enough
+  to feel it. Do not reintroduce a per-message `duration`, and do not "simplify" the
+  unchanged-velocity check away.
+- **`_expire_jog` is the deadman, not bookkeeping.** Nothing else stops an arm whose sender
+  died mid-jog: the controller holds the velocity indefinitely. It must command the stop,
+  not merely report `ready` — an arm travelling while the node says idle is worse than no
+  expiry at all.
 - This controls a real robot. Test changes carefully and preserve the safety checks: the
   reachability check before a move, the arrival confirmation after it, and the live error
   reads that make both of them mean anything.

README.md

@@ -123,8 +123,7 @@ you see `done`. Sending them all at once does not queue them; the last one wins.
 
 ## Jogging
 
-`jog` is a topic, not a service: a velocity command expires on the controller's own TTL,
+`jog` is a topic, not a service: a sender keeps sending and nobody waits for an answer.
-so a sender keeps sending and nobody waits for an answer.
 
 ```python
 node.send_output("jog", pa.array([{"velocity": [20.0, 0, 0, 0, 0, 0]}]))
@@ -132,9 +131,18 @@ node.send_output("jog", pa.array([{"velocity": [20.0, 0, 0, 0, 0, 0]}]))
 
 It still drives the arm, so it behaves like a motion where that matters: the first
 non-zero jog preempts a motion in play and `robot_state` turns to `moving`. A zero
-velocity stops it, and so does simply going quiet — the node returns to `ready` once
+velocity stops it, and so does simply going quiet — the node stops the arm and returns to
-`VELOCITY_COMMAND_TTL_S` has passed, because that is when the controller has expired the
+`ready` once `VELOCITY_COMMAND_TTL_S` has passed.
-command.
+
+**The velocity is set once and held.** The controller is given a velocity with no
+duration, so it keeps it until a different one arrives: re-sending an unchanged velocity
+does not reach the arm at all. Sending it repeatedly re-armed a timed segment and made the
+controller re-plan the same motion, which on a real arm is felt as stepping rather than
+travel — even at four messages a second.
+
+That also means **the controller no longer stops the arm on its own**, so
+`VELOCITY_COMMAND_TTL_S` is enforced here instead. It is a real deadman now rather than a
+description of one: a sender that dies mid-jog is what it exists for.
 
 ## Telemetry
 
@@ -157,7 +165,7 @@ Add to your dataflow:
 nodes:
   - id: ulite6
     git: ssh://git@gitea.liria.cl:5001/liria/dora-ulite6.git
-    tag: v0.3.0
+    tag: v0.3.1
     build: pip install .
     path: dora-ulite6
     inputs:
@@ -239,13 +247,13 @@ left where it stood.
 | `READY_TIMEOUT_S` | `3.0` | How long `recover` waits for a movable state |
 | `HOME_TIMEOUT_S` | `20.0` | How long homing may take |
 | `TOOL_SETTLE_S` | `2.0` | How long to wait for suction to build or fingers to close |
-| `VELOCITY_COMMAND_TTL_S` | `0.5` | The controller's own expiry for one `jog` command |
+| `VELOCITY_COMMAND_TTL_S` | `0.5` | How long a `jog` stream may go quiet before this node stops the arm |
 
 ## Development
 
 ```bash
 uv sync --group dev
-uv run pytest      # 86 tests, no robot needed
+uv run pytest      # 92 tests, no robot needed
 uv run ruff check .
 ```
 

dora-node.yml

@@ -49,9 +49,15 @@ inputs:
     description: >-
       A continuous velocity command: a one-row struct {velocity} of 6 numbers
       [vx, vy, vz, wx, wy, wz] in mm/s and deg/s. A topic rather than a service
-      because it expires on the controller's own TTL and a sender must keep
+      because a sender keeps sending and nothing is published in answer. It
-      sending; nothing is published in answer. It drives the arm, so the first
+      drives the arm, so the first non-zero one preempts a motion in play and
-      non-zero one preempts a motion in play and robot_state turns to moving.
+      robot_state turns to moving.
+
+      The velocity is set on the controller once and held: an unchanged one is
+      not sent to the arm again, because re-arming it makes the controller
+      re-plan the same motion and the arm step rather than travel. A sender that
+      goes quiet for longer than VELOCITY_COMMAND_TTL_S is stopped by this node,
+      which is the deadman behind a sender that dies mid-jog.
 
 outputs:
   response:
@@ -112,7 +118,7 @@ env:
 example: |
   - id: ulite6
     git: ssh://git@gitea.liria.cl:5001/liria/dora-ulite6.git
-    tag: v0.3.0
+    tag: v0.3.1
     build: pip install .
     path: dora-ulite6
     inputs:

dora_ulite6/config.py

@@ -60,9 +60,10 @@ class MotionConfig:
     ready_timeout_s: float = 3.0
     home_timeout_s: float = 20.0
     tool_settle_s: float = 2.0
-    # The controller's own expiry for one jog command: the arm keeps moving at
+    # How long a jog stream may go quiet before this node stops the arm. The
-    # the commanded velocity until this runs out, so a sender that stops sending
+    # velocity is set on the controller once and held there indefinitely — see
-    # stops the arm.
+    # `ULite6.set_cartesian_velocity` — so nothing expires it but us: this is
+    # the deadman behind a sender that dies mid-jog, enforced by `_expire_jog`.
     velocity_command_ttl_s: float = 0.5
 
     @classmethod

dora_ulite6/control.py

@@ -575,16 +575,24 @@ class Control:
     # --- the reporter thread ---
 
     def _expire_jog(self) -> None:
-        """Stop calling the arm jogging once the controller has expired the command.
+        """Stop the arm once the sender driving it has gone quiet.
 
-        A jog lives on the controller's own TTL, so a sender that goes quiet
+        **This is the deadman, not bookkeeping.** The velocity is set on the
-        leaves an arm that stopped moving a moment later. Nothing tells us; the
+        controller once and held there indefinitely — see
-        clock does.
+        :meth:`ULite6.set_cartesian_velocity` for why it cannot be given a
+        duration — so a sender that dies mid-jog leaves an arm that travels
+        until something says otherwise. Nothing tells us; the clock does, and
+        this is what says otherwise.
+
+        The stop goes through the job queue rather than the arm directly: this
+        runs on the reporter thread, and the control thread is the only one that
+        may touch the driver.
         """
         with self._lock:
             if not self._jogging or time.monotonic() - self._last_jog < self.config.motion.velocity_command_ttl_s:
                 return
             self._jogging = False
+        self._jobs.put(Jog(velocity=[0.0] * 6))
         self._idle_unless_busy()
 
     def _run_reporter(self) -> None:

dora_ulite6/driver.py

@@ -61,6 +61,10 @@ class ULite6:
         # falls back to a blocking get_position().
         self.arm = XArmAPI(self.ip, do_not_open=True, enable_report=True)
         self._velocity_mode = False
+        # The velocity currently standing on the controller. A velocity is a
+        # set-point it holds, so re-sending an unchanged one is not a no-op: see
+        # `set_cartesian_velocity`.
+        self._commanded: list | None = None
         self.connect()
 
     # --- connection ---
@@ -500,10 +504,24 @@ class ULite6:
     def set_cartesian_velocity(self, velocity: list) -> None:
         """Drive the arm at a constant base-frame velocity (xArm mode 5) and return.
 
-        ``velocity`` is ``[vx, vy, vz, wx, wy, wz]`` in mm/s and deg/s. The arm
+        ``velocity`` is ``[vx, vy, vz, wx, wy, wz]`` in mm/s and deg/s. The
-        keeps moving until the controller's own TTL expires or a new velocity
+        controller holds it until a different one arrives or an all-zero vector
-        arrives, so a sender must keep sending; an all-zero vector stops it and
+        stops it and leaves velocity mode.
-        leaves velocity mode.
+
+        **The velocity is set once and then left alone.** ``duration=0`` is the
+        SDK's "always effective, will not stop automatically", and an unchanged
+        velocity is not sent again at all. Both halves matter: this used to pass
+        ``duration=velocity_command_ttl_s`` on every message, which re-armed a
+        timed segment several times a second and made the controller re-plan the
+        same motion over and over. On a real arm that is not smooth travel — an
+        operator feels it as the arm moving in steps. Re-arming even four times a
+        second is enough to produce it, so the answer is not to re-arm less
+        often but not to re-arm at all.
+
+        Dropping ``duration`` means the controller no longer stops the arm by
+        itself, so the expiry that backs a sender going quiet has to be enforced
+        here instead: :meth:`Control._expire_jog` commands the stop that the
+        controller's timer used to.
         """
         self._require_connection()
         if any(velocity):
@@ -511,12 +529,19 @@ class ULite6:
                 self.arm.set_mode(MODE_CARTESIAN_VELOCITY)
                 self.arm.set_state(0)
                 self._velocity_mode = True
+                # Every route out of velocity mode comes back through here, so
+                # this is the one place the standing velocity has to be
+                # forgotten — re-entering the mode must always re-send.
+                self._commanded = None
+            if velocity == self._commanded:
+                return
             code = self.arm.vc_set_cartesian_velocity(
                 velocity,
                 is_radian=False,
                 is_tool_coord=False,
-                duration=self.motion.velocity_command_ttl_s,
+                duration=0,
             )
+            self._commanded = list(velocity)
             self._check_motion_code(code, "set_cartesian_velocity")
             return
         if self._velocity_mode:

pyproject.toml

@@ -1,6 +1,6 @@
 [project]
 name = "dora-ulite6"
-version = "0.3.0"
+version = "0.3.1"
 description = "Dora node for a UFactory Lite6 arm: motion and control services, and joint and tool-pose telemetry"
 readme = "README.md"
 license = { text = "MIT" }

tests/test_driver.py

@@ -0,0 +1,104 @@
+"""The driver's half of velocity control: what actually reaches the controller.
+
+`FakeArm` stands in for this whole class everywhere else, so nothing else in the
+suite can see what the driver says to the SDK. That is the one thing worth
+pinning here: a velocity is a set-point the controller holds, and how often it is
+re-sent is the difference between an arm that travels and an arm that steps.
+"""
+
+import pytest
+
+from dora_ulite6.config import Config
+from dora_ulite6.driver import ULite6
+
+MOVE = [20.0, 0.0, 0.0, 0.0, 0.0, 0.0]
+BACK = [-20.0, 0.0, 0.0, 0.0, 0.0, 0.0]
+STILL = [0.0] * 6
+
+
+class FakeSDK:
+    """Just enough XArmAPI to build a driver and watch it command a velocity."""
+
+    def __init__(self, *args, **kwargs):
+        self.connected = True
+        self.mode = None
+        self.velocities = []
+
+    def connect(self):
+        self.connected = True
+
+    def disconnect(self):
+        self.connected = False
+
+    def motion_enable(self, enable=True):
+        pass
+
+    def set_mode(self, mode):
+        self.mode = mode
+
+    def set_state(self, state):
+        pass
+
+    def vc_set_cartesian_velocity(self, speeds, is_radian=None, is_tool_coord=False, duration=-1):
+        self.velocities.append((list(speeds), duration))
+        return 0
+
+
+@pytest.fixture
+def robot(monkeypatch):
+    """Return a driver over a fake SDK, with the calls it made on `arm`."""
+    monkeypatch.setattr("dora_ulite6.driver.XArmAPI", FakeSDK)
+    return ULite6(Config())
+
+
+def commanded(robot):
+    """Return every velocity the driver put on the controller."""
+    return [speeds for speeds, _ in robot.arm.velocities]
+
+
+def test_a_velocity_is_never_given_a_duration(robot):
+    # `duration` makes the controller stop the arm on its own, which means every
+    # message re-arms a timed segment and the controller re-plans the same
+    # motion. The SDK reads 0 as "always effective, will not stop
+    # automatically", which is what lets one command stand.
+    robot.set_cartesian_velocity(MOVE)
+
+    assert [duration for _, duration in robot.arm.velocities] == [0]
+
+
+def test_a_held_velocity_reaches_the_controller_once(robot):
+    # The arm holds it, so saying it again says nothing new — and saying it
+    # again several times a second is what an operator feels as stepping.
+    for _ in range(5):
+        robot.set_cartesian_velocity(MOVE)
+
+    assert commanded(robot) == [MOVE]
+
+
+def test_a_changed_velocity_reaches_the_controller(robot):
+    # Sending once is worth nothing if a new direction is taken for the old one.
+    robot.set_cartesian_velocity(MOVE)
+    robot.set_cartesian_velocity(BACK)
+
+    assert commanded(robot) == [MOVE, BACK]
+
+
+def test_a_zero_velocity_stops_the_arm_and_leaves_velocity_mode(robot):
+    robot.set_cartesian_velocity(MOVE)
+
+    robot.set_cartesian_velocity(STILL)
+
+    assert commanded(robot) == [MOVE, STILL]
+    assert robot._velocity_mode is False
+
+
+def test_the_same_velocity_is_sent_again_after_leaving_velocity_mode(robot):
+    # Leaving the mode clears what the controller was holding, so the velocity
+    # it had before means nothing on the way back in. Remembering it across the
+    # gap would leave the arm still while the operator held a direction.
+    robot.set_cartesian_velocity(MOVE)
+    robot.set_cartesian_velocity(STILL)
+
+    robot.set_cartesian_velocity(MOVE)
+
+    assert commanded(robot) == [MOVE, STILL, MOVE]

tests/test_lifecycle.py

@@ -205,8 +205,7 @@ def test_a_zero_velocity_jog_does_not_make_a_running_motion_look_idle(monkeypatc
 
 
 def test_a_sender_that_goes_quiet_stops_being_called_jogging(monkeypatch):
-    # The controller expires the command on its own; nothing tells us, so the
+    # Nothing tells us a sender died, so the clock has to.
-    # clock has to.
     control = build(monkeypatch, motion=MotionConfig(velocity_command_ttl_s=0.02))
     try:
         wait_for(lambda: READY in control.take_state_changes())
@@ -218,6 +217,22 @@ def test_a_sender_that_goes_quiet_stops_being_called_jogging(monkeypatch):
         control.shutdown()
 
 
+def test_a_sender_that_goes_quiet_actually_stops_the_arm(monkeypatch):
+    # The velocity is held by the controller indefinitely, so the expiry is the
+    # deadman itself and not a note about one. Reporting `ready` without
+    # commanding the stop would leave the arm travelling while the node said it
+    # was idle, which is worse than not expiring it at all.
+    control = build(monkeypatch, motion=MotionConfig(velocity_command_ttl_s=0.02))
+    try:
+        wait_for(lambda: READY in control.take_state_changes())
+        control.start_jog([20.0, 0, 0, 0, 0, 0])
+        wait_for(lambda: ("jog", [20.0, 0, 0, 0, 0, 0]) in control.arms[0].calls)
+
+        wait_for(lambda: ("jog", [0.0] * 6) in control.arms[0].calls)
+    finally:
+        control.shutdown()
+
+
 def test_a_jog_preempts_a_motion_that_is_running(monkeypatch):
     control = build(monkeypatch)
     control.arms[0].block = threading.Event()

uv.lock

@@ -41,7 +41,7 @@ wheels = [
 
 [[package]]
 name = "dora-ulite6"
-version = "0.3.0"
+version = "0.3.1"
 source = { editable = "." }
 dependencies = [
     { name = "dora-rs" },